Arcam SOLO MINI Operations Instructions download pdf (Page 2)

safety

guidelines

Important safety instructions

This product is designed and manufactured to meet

strict quality and safety standards. However, you should

be aware of the following installation and operation

precautions.

1. Take heed of warnings and instructions

You should read all the safety and operating

instructions before operating this equipment. Retain

this handbook for future reference and adhere to all

warnings in the handbook or on the equipment.

2. Water and moisture

The presence of electricity near water can be

dangerous. Do not use the equipment near water – for

example next to a bathtub, washbowl, kitchen sink, in a

wet basement or near a swimming pool, etc.

3. Object or liquid entry

Take care that objects do not fall and liquids are not

spilled into the enclosure through any openings. Liquid-

lled objects such as vases should not be placed on the

equipment.

4. Placing the equipment

Only use a rack or shelf that is stable and strong

enough to support the weight of this equipment.

5. Ventilation

Do not place the equipment on a bed, sofa, rug or

similar soft surface, or in an enclosed bookcase

or cabinet, since ventilation may be impeded. We

recommend a minimum distance of 50mm around the

sides and top of the equipment to provide adequate

ventilation.

5. Heat

Locate the equipment away from naked ames or heat-

producing appliances such as radiators, stoves or other

appliances that produce heat.

6. Climate

The equipment has been designed for use in moderate

climates and in domestic situations.

8. Cleaning

Unplug the unit from the mains supply before cleaning.

The case should normally only require a wipe with a

soft, lint-free cloth. Do not use chemical solvents for

cleaning.

We do not advise the use of furniture cleaning sprays

or polishes as they can cause indelible white marks.

9. Power sources

Only connect the equipment to a power supply of

the type described in the operating instructions or as

marked on the equipment.

The primary method of isolating Solo Mini from the

mains supply is to use the switch on the rear of the

unit. Solo Mini must be installed in a manner that makes

disconnection possible.

10. Power-cord protection

Power supply cords should be routed so that they are

not likely to be wa ked on or pinched by items placed

upon or against them. Pay particular attention to the

point where they exit from the equipment.

11. Power lines

Locate any outdoor antenna/aerial away from power

lines.

12. Non-use periods

If the equipment is not being used for an extended

period, we recommend that you unplug the power cord

of the equipment from the outlet, to save power.

13. Abnormal smell

If an abnormal smell or smoke is detected from the

equipment, turn the power off immediately and unplug

the equipment from the wall outlet. Contact your

dealer and do not reconnect the equipment.

14. Servicing

You should not attempt to service the equipment.

Contact your dealer to arrange servicing.

15. Damage requiring service

The equipment should be serviced by qualied service

personnel when:

A. the power-supply cord or the plug has been

damaged, or

B. objects have fallen, or liquid has spilled into the

equipment, or

C. the equipment has been exposed to rain, or

D. the equipment does not appear to operate

normally or exhibits a marked change in

performance, or

E. the equipment has been dropped or the

enclosure damaged.

Safety compliance

This equipment has been designed to meet the IEC/EN

60065 international electrical safety standard.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

WARNING:

Due to the mains switch being located on the rear

panel, the apparatus must be located in an open area

without anything obstructing access to the mains

switch.

Mains plug/appliance coupler is used to disconnect

device and it shall remain readily operable.

Correct Disposal of this product

This marking indicates that this product

should not be disposed with other

household waste throughout the EU.

To prevent possible harm to the

environment or human health from

uncontrolled waste disposal and to

conserve material resources, this product should be

recycled responsibly.

To dispose of your product, please use your local

return and collection systems or contact the retailer

where the product was purchased.

Class II product

This equipment is a Class II or double

insulated electrical appliance. It has been

designed in such a way that it does not

require a safety connection to electrical

earth (‘ground’ in the U.S.).

Many of these items are common sense precautions but, for your own safety and to ensure that you do not damage the unit, we recommend that you read them.

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

ATTENTION

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer

servicing to qualified service personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of

uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: In Canada and the USA, to prevent electric shock, match the wide blade of the plug to the wide slot

in the socket and insert the plug fully into the socket.

The screw on the base of the unit

indicated by the warning triangle is a

critical component.

For safety reasons, only replace with

a screw of identical size – or one not

exceeding 8mm in length.

1 2 3 4 5 6 7 ... 17 18

Comments to this Manuals

No comments

Arcam SOLO MINI Operations Instructions Page 2

Comments to this Manuals