Arcam SOLO MOVIE 2.1 Operations Instructions download pdf (Page 17)

E-17

movie 2.1

solo

English

This section describes how to use the on-screen display

set-up menus to ﬁne-tune Solo Movie 2.1 in relation

to the other items in your system – such as your video

display and speakers – and to conﬁgure some personal

preferences.

Obtaining a picture

To view the Set-up menu for the initial conﬁguration, we

recommend the use of the composite video output to

connect to your display device. This is because the high

quality video output has several display modes and may

be incompatible with your display device in its default

conﬁguration.

Ensure that your display device is switched on and that

you have selected the correct video input. You should

see the screen shown below. This is the image that Solo

Movie 2.1 gives when there is no disc playing.

The Display set-up menu

For optimum video performance it may be necessary to

conﬁgure your display for the video source – Solo Movie

2.1, in this case. A series of test patterns generated by

Solo Movie 2.1 allows you to optimize colour balance,

contrast, brightness and to centre your picture. Full

instructions for each test pattern are displayed on the

screen before the test pattern is shown.

To enter the Display set-up menu, move the cursor

down to the ‘Display’ button on the screen and press

OK.

Follow the on-screen instructions and press SETUP at any

time to quit from a page (or press OK on the last screen

to Exit).

advanced

set-up

Using the Set-up menus

Your Solo Movie 2.1 has two different set-up menus:

The Set-up menu allows conﬁguration of all

aspects of Solo Movie 2.1. Conﬁgurable items

and their potential values are described on the

following pages.

The Display set-up menu is a series of video

test patterns with instructions that help you to

optimize your display for Solo Movie 2.1.

Remember that to use the CR100 remote

control for advanced set-up, you ﬁrst have to set

it to DVD mode by pressing the

DVD button.

The Set-up menus

To enter the Set-up menus:

Either: press and hold the front panel

MENU button for

more than one second.

Or: using the remote control, press the

DVD button to

ensure that the CR100 is in DVD mode, and then

press the SETUP button.

You can press

MENU (front panel) or SETUP (remote

control) at any time to quit from a page and save all the

settings.

The Set-up menu comprises four pages of options:

Operational setup

Video setup

Audio setup

Speaker setup.

The tabs on the left side of the screen show the pages

available. To change between pages, move the menu

highlight to the appropriate tab (using the

and

buttons).

To change an item, ﬁrst use the

controls to

highlight the item, then press OK to open the list of

options for the menu item. The current option for the

menu item is ticked. Select a new option using the

controls and conﬁrm the selection with OK. (If

the item to be changed is controlled by a slider, press OK

to activate the slider, move it using the

controls,

conﬁrming the setting with OK.)

Note that options that are not currently applicable are

shown ‘greyed out’, and cannot be highlighted or changed.

Screen saver

To protect your screen from damage from a persistent

static image, a screen saver starts after a few minutes

of inactivity.

An Arcam logo appears at random locations around

the screen. To restore the previous screen image, press

the

(stop) button on the front panel or the remote

control.



1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 29 30

Comments to this Manuals

No comments

Arcam SOLO MOVIE 2.1 Operations Instructions Page 17

Comments to this Manuals

Related products and manuals for DVD players Arcam SOLO MOVIE 2.1