Arcam SOLO MOVIE 2.1 Operations Instructions Page 26
- Page / 30
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
E-26
clock/alarm
Setting the clock and alarm
When Solo Movie 2.1 is in clock mode (POWER light showing red), press MENU to set the clock
or alarms.
Use the left and right buttons on the remote control to select the item to change, then use the
up and down buttons to change the value. For example, after pressing
MENU to enter the clock/
alarm setting menu, pressing up and down will change between setting the clock and setting
one of the alarms.
Solo Movie 2.1 allows up to four different alarms to be set. In this way, different users of Solo
Movie 2.1 can have their personal alarm settings, or you could set up different alarms for
different circumstances (work and holiday periods, for example).
Stopping or pausing an alarm
To stop an alarm ringing, press the power button on the front-panel or remote control.
Alternatively, press
OK to enter ‘snooze’ mode; the alarm will re-sound after a 10-minute delay.
Please note that you must be in AMP, DVD or TUN mode on the CR100 to stop or pause an
alarm from the remote control. To cancel snooze-mode, press the power button.
Sleep timer
This timer allows you to specify a listening period, after which Solo switches automatically into
stand-by. The period can be set in 5-minute intervals, up to 120 minutes (2 hours): a count-
down timer is displayed on the front panel. To set the sleep timer, press the MENU key on the
front panel (or AMP then MENU key on the remote control) to access the Amplifier menu (see
page 15).
Alarms
Remember to set the time-of-day on the clock,
otherwise alarms and countdown sleep timers will
not work!
Retaining clock settings
If Solo Movie 2.1 is turned off at the mains supply,
clock settings are retained for approximately four
days. In the low power consumption ‘hard stand-by’
mode, clock settings are retained indefinitely.
Set 12/24
hour clock
12HR
24HR
Set the time
(hours)
Earlier
Later
Set the time
(minutes)
Earlier
Later
Set the
day
Previous
Next
Confirm
settings
Exit to
time-of-day
display
Clock mode
Exit to
time-of-day
display
Clock mode
Alarms go off at the scheduled time for selected
days. In this example, alarms are set to go
off on Monday, Wednesday and Friday.
Off
On
Set alarm
on or off
Earlier
Later
Set hours for
alarm
Set minutes for
alarm
Earlier
Later
Select a signal source
(DAB only where fitted)
Off
On
Set alarm days on
or off
Setting the clock
Setting alarms
Setting the front panel clock
The procedure is shown on the diagram below, but
the instructions are:
1. Power off the unit, using the front panel
POWER button, or the remote control
2
button. The light next to the front panel
POWER button glows red, showing that the
unit is in ‘Clock’ mode’
2. Press the remote control MENU button once.
3. Press
B
once to enter the Clock Set
screen.
4. Press
E
to highlight 12HR or 24HR; toggle with
the
BC
cursor keys.
5. Press
E
to move to the hours; adjust with the
BC
cursor keys.
6. Press
E
to move to the minutes; adjust with
the
BC
cursor keys.
7. Press
E
to move to set the day; adjust with
the
BC
cursor keys.
8. Press
E
to move to Set? and confirm with
OK.
Press the
2
button to save and exit the menu.
- Handbook 1
- Handbuch 1
- Handleiding 1
- Important safety instructions 2
- Safety compliance 2
- Contents 3
- � 4
- Interconnect cables 6
- COMPOSITE VIDEO OUT socket 8
- MUTE control 8
- SUB output using an 9
- Important – before you start 10
- Zone 2 volume control 11
- Radio interference 12
- Inserting batteries into the 13
- The CR100 Universal remote 13
- Source keys 13
- DVD/CD playback 14
- Maintaining reliability 14
- Tuner commands 14
- Amp commands 14
- MENU button or DVD then MENU 15
- SUB (subwoofer, or LFE 16
- Obtaining a picture 17
- Using the Set-up menus 17
- Operational set-up 18
- Video set-up 18
- ZONE 2/REC OUT rear 19
- SETUP on the 20
- SETUP at any time 20
- MENU SOURCE INFO OK 21
- Listening to CD/DVD-Audio 22
- Basic operation 22
- MENU adds the file to 23
- PLAY or OK plays the 23
- TUN button on the remote 24
- TUN button 24
- Searching for stations 25
- Setting station presets 25
- Selecting station presets 25
- Retaining clock settings 26
- Setting the front panel clock 26
- Problems with video 28
- Problems with audio 28
- Worldwide Guarantee 29
- Claims under guarantee 29
- Continual improvement policy 29
- Problems? 29
Related products and manuals for DVD players Arcam SOLO MOVIE 2.1
DVD players Arcam DV78 Specifications
(100 pages)
(100 pages)
DVD players Arcam DV27 Specifications
(21 pages)
(21 pages)
DVD players Arcam DV78 Specifications
(24 pages)
(24 pages)
DVD players Arcam DV27A Specifications
(23 pages)
(23 pages)
DVD players Arcam DV88 User Manual
(28 pages)
(28 pages)
DVD players Arcam DV137 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.361 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals